For instance, when you can’t reach a device, so you try pinging it. The ping test shows the host as unreachable and zero packet loss. Even if you’re tech-savvy, this situation might put a huge question mark above your head. However, we’re here to demystify this issue once and for all.

What does it mean when ping says destination host unreachable?

The destination host unreachable error message denotes that the host you are trying to ping is down. This error might also mean the host is not returning to ICMP echo requests.

Why is the destination host unreachable?

There are many reasons why a host can be or become unreachable. Even if you’re on the same network, the target device (host) might have different connection settings then you, an aggressive firewall, or even some spoofing, so you can’t exactly pinpoint the main cause. Here’s a list of the most common reasons why the host might be unreachable:

The target computer might be off An overly-protective firewall that blocks any incoming requests Improper cable connection Spoofing Misconfiguration of Default Gateway on the source PC (yours)

The point is that if you can’t reach a host, it’s mainly because there’s no route from the local device (yours) to the remote one (host). Either that or something blocks your attempts to connect to the hosts. Nevertheless, your pings never reach their destination, and still, there’s no reported packet loss.

Destination host unreachable but no packet loss

Ping and packet loss are somewhat tied, but they’re entirely different. For once, ping tests the reachability of certain devices (hosts), whereas packet loss is the percentage of packets that didn’t reach the destination. So why there’s no packet loss even though the ping destination host is unreachable? The answer is quite simple. If there’s no route from the local system (yours), then the packets you sent were never placed on the route. Therefore, the requests will always have a 0% packet loss since nothing was sent. Trivia fact: on most Linux systems, pinging reports 100% packet loss.

Destination host unreachable routing issue

If you’ve encountered this issue before, you’ve most likely seen one of these two errors:

Destination Host Unreachable – this error occurs whenever there’s no route between the local system and the destination Reply from x.x.x.x: Destination Host Unreachable – there’s something wrong with a remote router (x.x.x.x is the IP address of the troublesome router)

There’s yet another scenario when your request time out. After sending echo requests, the PC starts listening for echo replies. The default waiting time for an echo reply is one second. SPONSORED If the device doesn’t receive the reply within 1 second, the request will time out, and you’ll receive a suggestive error message (i.e., Request Timed Out). This situation is mainly caused by network congestion but can also have other causes. For instance, silent discards, poorly routed networks, or packet filtering can contribute to request timeouts.

How to fix destination host unreachable ping?

If the cause of the error is improper Default Gateway configuration, we’ll show you how to fix it. Perform the following steps:

1. Confirm your default gateway

If the Default Gateway shown is different from your IP address, you need to proceed to the next stage to change it.

2. Change Default Gateway

After restarting your PC, try to ping the host again and check if you still get the Destination host unreachable error. If you are still getting the error, you should disable your firewall and check if the host device is on and connected. You can also check the network cables to be sure they are fine.

You can get 0% packet loss, even when hosts are unreachable

Long story short, you shouldn’t stress over a simple semantics issue. Even if Windows’ ping tool reports 0% packet loss, it’s because there’s no connection and no packets are being sent. Just try using the ping tool in Linux, and you’ll probably receive a 100% packet loss. The important thing is to understand why such an error occurs and find ways to fix it. With this, we can conclude this extensive guide on how to fix the destination host unreachable error. If you are facing a similar issue in Hyper-V guest cannot ping the host, check our detailed guide to fix it quickly. Feel free to let us know how you fixed this issue in the comments below.

SPONSORED Name * Email * Commenting as . Not you? Save information for future comments
Comment

Δ